The Bosch AQ4 Powervent Kit with built-in freeze protection is designed for the Bosch 1600H (Hydro Ignition) and 1600P (Pilot) tankless water heaters. This accessory allows the Bosch 1600H and 1600P tankless heaters to vent horizontally out the sidewall of the home. The AQ4 does require power to operate and operates on 120V and comes with a 3' cord to plug into the outlet.
The AQ4 is a power vent kit and will allow a horizontal vent run of up to 25 feet with one elbow (subtract 5 feet for every elbow). This kit includes the power vent motor. There is also a vent hood with damper that gets mounted on the outside of the home and this built in flapper prevents the cold air from coming in when the heater is not in use. Please make sure to refer to the installation manual and that the hood is properly installed so that the flapper stays closed all the way when not in use.
The AQ4 powervent kit comes with a 5" to 4" reducer. This reducer fits right on top of the heater and then you would use 4" type B, C or stainless steel AL29-4C venting (not included) to go to the powervent motor. There is a minimum of 2 feet of straight pipe required between the reducer and the blower motor. Any venting (if needed) "after" the powervent motor must be 4" sealed stainless steel AL29-4C. The Blower motor should be placed right at the opening where the termination hood with damper is to be installed on the sidewall of the home.
The AQ4 powervent kit is activated by a flow switch and gets attached to the cold water pipe on the right side of the unit just before it goes into the heat exchanger.
The blower motor for the AQ4 has a new design and includes a delay setting that goes from #1 - #5 and this lets the installer set the blower motor so that when it senses flow it can be delayed for 1 - 5 seconds before the blower comes on. This will help to ensure the pilot and burners light without getting sucked out by the blower motor.
There is also a built in safety spill switch that gets attached to the tankless water heater and this will detect high temperatures from any flue gases in the case the blower motor does not activate and will shut the unit completely down.
Friday, January 25, 2013
Wednesday, December 26, 2012
Timers for Ariston Mini-Tank Water Heaters
Globaltowne now has timers for the Ariston Mini-Tank water heaters. Call to order - 888-726-9752
By using a 24 hour or 7 day timer you can save money by turning off the water heater during times when you are sleeping or not at home. The Ariston's take from 15 to 30 minutes to heat up. Set the timer to turn off the heater at a time when no one will require hot water, then set the timer to turn the heater back on 15 to 30 minutes before hot water is needed. The 24 hour or 7 day timer can handle up to 15 amps and has a three prong 120 volt plug. The 24 hour timer can be set for up to 24 on or off times per day. The 7 day timer can be set for up to 6 on or off times per day.
To Install, plug the timer into a standard outlet or GFCI protected outlet and then plug the heater into the socket on the timer. Use the tabs to set the times on the timer for the on and off cycles. Now your heater will not be using power when it is not necessary.
INDOOR 7-DAY MECHANICAL TIMER, 3-CONDUCTOR
Save money and reduce energy costs by using our 7 day mechanical timer that automatically turns devices on and off at programmed times. Come home to hot water or a lighted house by using a timer to turn on and off heaters, lights, seasonal displays or electric candles so you can enjoy your decorations without having to turn them on and off. Set up to 6 on/off events per day. Settings repeat weekly, with the option to program each day different for added flexibility. The segment pins are permanently attached so they won't get lost. This timer features warm neutrals which compliment today's home interior and instruction slot for easy-to-find programming manual. This timer is compatible with compact fluorescent lighting, LED bulbs and CSA certified for quality assurance.
Indoor 24-Hour Heavy Duty Mechanical Timer, 3-Conductor
Our 24 hour mechanical timer can be set for multiple on/off events, which maximizes energy savings and controls electricity costs by only using power when it's needed. This plug-in timer provides up to 24 on/off settings per day and the cycle repeats every 24 hours and designed with a warm neutral color pallet to compliment today's home interior. Would you like to come home to hot water or a lighted house at the end of the day? Switch on a fan at the same time every afternoon to cool a certain room? This timer makes it easy; just plug a lamp, fan, water heater or other electrical appliance in, set the timer and walk away. This timer is compatible with compact fluorescent lighting, LED bulbs and CSA certified for quality assurance.
By using a 24 hour or 7 day timer you can save money by turning off the water heater during times when you are sleeping or not at home. The Ariston's take from 15 to 30 minutes to heat up. Set the timer to turn off the heater at a time when no one will require hot water, then set the timer to turn the heater back on 15 to 30 minutes before hot water is needed. The 24 hour or 7 day timer can handle up to 15 amps and has a three prong 120 volt plug. The 24 hour timer can be set for up to 24 on or off times per day. The 7 day timer can be set for up to 6 on or off times per day.
To Install, plug the timer into a standard outlet or GFCI protected outlet and then plug the heater into the socket on the timer. Use the tabs to set the times on the timer for the on and off cycles. Now your heater will not be using power when it is not necessary.
INDOOR 7-DAY MECHANICAL TIMER, 3-CONDUCTOR
Save money and reduce energy costs by using our 7 day mechanical timer that automatically turns devices on and off at programmed times. Come home to hot water or a lighted house by using a timer to turn on and off heaters, lights, seasonal displays or electric candles so you can enjoy your decorations without having to turn them on and off. Set up to 6 on/off events per day. Settings repeat weekly, with the option to program each day different for added flexibility. The segment pins are permanently attached so they won't get lost. This timer features warm neutrals which compliment today's home interior and instruction slot for easy-to-find programming manual. This timer is compatible with compact fluorescent lighting, LED bulbs and CSA certified for quality assurance.
Features:
- Up to 6 on/off settings per day, repeats weekly
- Programmable in 2 hour intervals
- 3-conductor outlet and plug
- Never lose pins cannot be removed or lost
- Instruction slot and manual override switch
Ratings:
- 125V ac, 60 Hz
- 15 Amp, 1875 Watt Resistive
- 8 Amp, 1000 Watt Tungsten
- 5 Amp Ballast
- CSA Certified C/US
Our 24 hour mechanical timer can be set for multiple on/off events, which maximizes energy savings and controls electricity costs by only using power when it's needed. This plug-in timer provides up to 24 on/off settings per day and the cycle repeats every 24 hours and designed with a warm neutral color pallet to compliment today's home interior. Would you like to come home to hot water or a lighted house at the end of the day? Switch on a fan at the same time every afternoon to cool a certain room? This timer makes it easy; just plug a lamp, fan, water heater or other electrical appliance in, set the timer and walk away. This timer is compatible with compact fluorescent lighting, LED bulbs and CSA certified for quality assurance.
Features:
- Up to 24 on/off settings per day, repeats daily
- Programmable in 30 minute intervals
- 3-conductor outlet and plug
- Never lose pins cannot be removed or lost
- Instruction slot and manual override switch
Ratings:
- 125V ac, 60 Hz
- 15 Amp, 1875 Watt Resistive
- 8 Amp, 1000 Watt Tungsten
- 5 Amp Ballast
- CSA Certified C/US
888-726-9752
Labels:
12.5 amps,
15 amps,
ariston,
Ariston mini-tank,
GL2.5,
GL2.5S,
GL2.5Ti,
GL4,
GL6 PLUS,
GL8Ti,
timer
Monday, December 17, 2012
SPECIAL SALE on 3" Stainless Steel Vent Kits for Bosch Tankless Water Heaters
GlobalTowne.com is pleased to offer very special discounted pricing on all 3" Z-Flex Stainless Steel Vent Kits! Our Z-Flex Z-Vent stainless steel venting is rated AL29-4C for Category III appliances.
We are offering unbelievably low pricing on the following 3" Z-Vent Stainless Steel Venting Kits:
We are offering unbelievably low pricing on the following 3" Z-Vent Stainless Steel Venting Kits:
- AQ3ES Horizontal Side Wall Vent Kit for Bosch 2700ES & 2400ES
- ES VVT Vertical Through-the-Roof Vent Kit for Bosch 2700ES & 2400ES & 660EF
- AQ5EF Horizontal Side Wall Vent Kit for Bosch 660EF
And, by popular demand, we have brought back our "PLUS" Kits which include extra items such as Surge Protectors, Auto-Reset GFCIs and WebStone Isolation Valve Kits. See the following Kits for details:
- AQ3ESPLUS 3" Stainless Steel Horizontal Vent Kit for Bosch 2700ES & 2400ES
- AQ5EFPLUS 3" Stainless Steel Horizontal Vent Kit for Bosch 660EF
If you find a similar 3" Stainless Steel Vent Kit product advertised for a price lower than ours just give us a call and we will beat their pricing -- guaranteed.
Please note that some of our competitors are advertising the AQ3ES Horizontal Vent Kit as a side-wall kit option for the Bosch 660EF. Be warned that the AQ3ES Vent Kit does not fit the bill! The AQ3ES Vent Kit is missing the correct Bosch 660EF Adaptor and the high temperature silicone sealant. And it has an air intake piece and gear clamps that are not needed with the Bosch 660EF heaters.
Lastly, our company is the only company selling the correct Bosch 660EF Adaptor. For several years the wrong adaptor was sold and we have worked directly with Z-Flex to develop a proper adaptor.
Steve
Tuesday, December 4, 2012
Bosch 660EF Side-Wall Vent Kit in Stainless Steel
GlobalTowne.com is the exclusive distributor for the AQ5EF 660EF Horizontal Vent Kit for the Bosch 660EF tankless water heaters.
The Bosch 660EF Side-wall Vent Kit comes with the Bosch 660EF Adaptor (2SVSWB03) and enugh Category III 3" Stainless Steel Vent Pipe to meet the 3' pipe length minimum specified on page 11 of the Bosch 660EF Installation Manual.
Also included in our 660EF side wall vent kit is a 3oz tube of high temperature silicone sealant, a wall thimble, a termination box with bird screen and a surge protector to protect the electronic components of the Bosch 660EF tankless water heater.
GlobalTowne.com is the *only* source for the correct Bosch 660EF Adaptor. Other adaptors on the market are either too small or too large to provide a proper seal with the flue collar on the heater. We worked directly with Z-Flex to develop a custom adaptor that properly fits the 660EF heaters.
We also carry the AQ5EFPLUS 660EF Horizontal Vent Kit which contains all parts from the AQ5EF kit PLUS a GFCI with an 18" extension cord and a Webstone 44443PR Isolation Valve Kit.
Steve
The Bosch 660EF Side-wall Vent Kit comes with the Bosch 660EF Adaptor (2SVSWB03) and enugh Category III 3" Stainless Steel Vent Pipe to meet the 3' pipe length minimum specified on page 11 of the Bosch 660EF Installation Manual.
Also included in our 660EF side wall vent kit is a 3oz tube of high temperature silicone sealant, a wall thimble, a termination box with bird screen and a surge protector to protect the electronic components of the Bosch 660EF tankless water heater.
GlobalTowne.com is the *only* source for the correct Bosch 660EF Adaptor. Other adaptors on the market are either too small or too large to provide a proper seal with the flue collar on the heater. We worked directly with Z-Flex to develop a custom adaptor that properly fits the 660EF heaters.
We also carry the AQ5EFPLUS 660EF Horizontal Vent Kit which contains all parts from the AQ5EF kit PLUS a GFCI with an 18" extension cord and a Webstone 44443PR Isolation Valve Kit.
Steve
Labels:
2SVSWB03,
660ef,
Adaptor,
aq5ef,
aq5efplus,
bosch,
category iii,
horizontal,
plus,
sealant,
side wall,
side-wall,
tankless water heater,
vent kit,
Vent Pipe,
venting,
Z-Flex,
Z-Vent
Wednesday, November 14, 2012
Bosch 660EF / 660EFO Tankless Water Heater Sale
GlobalTowne.com is pleased to announce a special sale on the Bosch Therm 660EF / 660EFO tankless water heaters.
GlobalTowne has a large quantify of the Bosch 660EF indoor tankless water heaters and 660EFO outdoor tankless water heaters and we are currently offering these heaters at special low prices.
If you are installing the Bosch 600EF indoor water heater you will need to vent it with 3" single wall stainless steel venting. We carry Z-Flex-Z-Vent 3" stainless steel category III vent pipe. You will also need the Z-Flex 2SVSWB03 Bosch 660EF adaptor. We have worked closely with Z-Flex to develop this adaptor. Our Bosch 660EF adaptor is the only one that will work properly with the Bosch 660EF heater.
The Bosch 660EFO outdoor tankless water heaters do not require any venting.
The Bosch 660EF / 660EFO tankless water heaters are 140,000 BTU maximum input heaters. They are very compact and are capable of providing hot water for one shower and a sink at the same time.
Steve
GlobalTowne has a large quantify of the Bosch 660EF indoor tankless water heaters and 660EFO outdoor tankless water heaters and we are currently offering these heaters at special low prices.
The Bosch 660EFO outdoor tankless water heaters do not require any venting.
The Bosch 660EF / 660EFO tankless water heaters are 140,000 BTU maximum input heaters. They are very compact and are capable of providing hot water for one shower and a sink at the same time.
Steve
Labels:
2SVSWB03,
660,
660ef,
660efo,
bosch,
indoor,
outdoor,
sale,
special,
tankless water heater,
therm
Wednesday, October 31, 2012
Auto Reset Ground Fault Circuit Interrupters (GFCIs)
As Hurricane Sandy rolled across the US East Coast I lost power twice. I have a 199,000 BTU Bosch Tankless Water Heater in my house that has an electronic ignition. I have my tankless water heater plugged into an Auto Reset GFCI with an 18" cord.
I didn't even think about it until this morning, but both times I lost power my tankless water heater was protected -- and I didn't even have to go down to my basement to reset my GFCI when the power was restored!
Most wall mounted Ground Fault Circuit Interrupters have the Auto Reset feature. But most GFCI extension cords do not have the Auto Reset feature. The GFCIs from GlobalTowne have this Auto Reset feature and this weekend it was appreciated.
Steve
I didn't even think about it until this morning, but both times I lost power my tankless water heater was protected -- and I didn't even have to go down to my basement to reset my GFCI when the power was restored!
Most wall mounted Ground Fault Circuit Interrupters have the Auto Reset feature. But most GFCI extension cords do not have the Auto Reset feature. The GFCIs from GlobalTowne have this Auto Reset feature and this weekend it was appreciated.
Steve
Tuesday, September 18, 2012
FLOW-AIDE by JC Whitlam ~ Now GREEN!
The New FLOW-AIDE DeScaler solution is now biodegradable for tankless Water Heaters.
The kit includes 500 GPH pump with 25 foot electrical cord, bucket, hoses (5') and quart of FLOW-AIDE descaler solution.
FLOW-AIDE is excellent for cleaning:
Heat Exchangers
Water Heaters
Evaporators
Boilers
Condensers
Humidifiers
Potable Water Lines
Thermal Solar Panels
RUST, LIME and SCALE
Please note that using the deScaler solution is most easily achieved with Isolation Valves.
Globaltowne's PLUS kit includes the WEBSTONE isolation valves for ease of use.
The kit includes 500 GPH pump with 25 foot electrical cord, bucket, hoses (5') and quart of FLOW-AIDE descaler solution.
FLOW-AIDE is excellent for cleaning:
Heat Exchangers
Water Heaters
Evaporators
Boilers
Condensers
Humidifiers
Potable Water Lines
Thermal Solar Panels
RUST, LIME and SCALE
Please note that using the deScaler solution is most easily achieved with Isolation Valves.
Globaltowne's PLUS kit includes the WEBSTONE isolation valves for ease of use.
The Flow-Aide Descaling PLUS Kit includes the following:
- 1 - 3.5 Gallon Bucket
- 1 - 350 GPH Pump
- 2 - 5 Foot Rubber Hoses
- 1 - Quart Flow-Aide
- 1 - Webstone Isolation Valve Kit (44443PR) with PRV
Please visit www.Globaltowne.com or call us at 888.726.9752
Bosch Heaters are LOW NOx
Bosch Therm Units meet low NOx - Gas Tankless Water Heaters
Bosch Thermotechnology North America, a leading provider of energy efficient water heaters, heating and air conditioning comfort systems as well as high quality solar thermal systems for commercial and residential use, announced today the following Therm tankless products from Bosch meet recently enacted Low emission (NOx) requirements passed by utility regulatory agencies in California and Vermont: Therm C 1210 ES/ESC; C 1050 ESC; 950 ES; 940 ES/ESO and 830 ES. All models offer NOx emissions of 14 ng/J or 20 ppm or less. California and Vermont are currently the first two states to enact the 14 ng/J or 20-ppm NOx level.
In accordance with the new guidelines as published in new Air Quality Management District (AQMD) ordinances, the following Bosch models will no longer be sold nor allowed for installation in areas that are subject to these AQMD ordinances: Therm 520 PN/HN; 330 PN, and 660 EF/EFO. AQMD’s are regulatory agencies supported by state government to help control and preserve air quality standards for a given area.
Therm units from Bosch include a unique design using a wide flame pattern and secondary dilution air that results in a lower flame temperature during the heating process. Combined with condensing technology, which utilizes a secondary heat exchanger to capture more heat from the exhaust for preheating incoming cold water, these models offer an attractive tankless water heating option that meets future code requirements today while offering optimal efficiency.
The complete Therm line from Bosch features models with updated software that delivers performance-enhancing characteristics including a minimum activation flow rate of 0.5 gallons per minute (GPM) and the ability on many models to cascade up-to-24 units for larger commercial applications. The Therm line includes ENERGY STAR® rated models, powered by natural gas or propane, which have an industry best 15-year warranty.
HVAC & plumbing professionals and affected homeowners in California and Vermont are encouraged to check with local regulatory agencies to ensure compliance of all tankless units with the new low NOx requirements.
www.prowaterheatersupply.com
commercial division of Global ProTankless Supply
1.866.289.4652
Bosch Thermotechnology North America, a leading provider of energy efficient water heaters, heating and air conditioning comfort systems as well as high quality solar thermal systems for commercial and residential use, announced today the following Therm tankless products from Bosch meet recently enacted Low emission (NOx) requirements passed by utility regulatory agencies in California and Vermont: Therm C 1210 ES/ESC; C 1050 ESC; 950 ES; 940 ES/ESO and 830 ES. All models offer NOx emissions of 14 ng/J or 20 ppm or less. California and Vermont are currently the first two states to enact the 14 ng/J or 20-ppm NOx level.
In accordance with the new guidelines as published in new Air Quality Management District (AQMD) ordinances, the following Bosch models will no longer be sold nor allowed for installation in areas that are subject to these AQMD ordinances: Therm 520 PN/HN; 330 PN, and 660 EF/EFO. AQMD’s are regulatory agencies supported by state government to help control and preserve air quality standards for a given area.
Therm units from Bosch include a unique design using a wide flame pattern and secondary dilution air that results in a lower flame temperature during the heating process. Combined with condensing technology, which utilizes a secondary heat exchanger to capture more heat from the exhaust for preheating incoming cold water, these models offer an attractive tankless water heating option that meets future code requirements today while offering optimal efficiency.
The complete Therm line from Bosch features models with updated software that delivers performance-enhancing characteristics including a minimum activation flow rate of 0.5 gallons per minute (GPM) and the ability on many models to cascade up-to-24 units for larger commercial applications. The Therm line includes ENERGY STAR® rated models, powered by natural gas or propane, which have an industry best 15-year warranty.
HVAC & plumbing professionals and affected homeowners in California and Vermont are encouraged to check with local regulatory agencies to ensure compliance of all tankless units with the new low NOx requirements.
www.prowaterheatersupply.com
commercial division of Global ProTankless Supply
1.866.289.4652
Thursday, July 19, 2012
Bosch Wireless Remote Control TSTAT2
The Bosch Wireless Remote Control TSTAT2 for the Bosch AquaStar 2700ES / 2400ES / 2400E / 2400EO / 250SX / 250SXO allows you to program your Bosch tankless gas water heater to a comfortable and safe temperature from around your home from a distance of up to 98 ft.
The TSTAT2 remote is particularly useful if you own a jacuzzi or hot tub that requires a hotter water temperature than you normally desire for regular shower use.
Please note that the electrical control of the Bosch AquaStar 2700ES / 2400ES / 2400E / 2400EO / 250SX / 250SXO must be removed and opened in order to install the wireless receiver circuit board to enable the use of the TSTAT2 Wireless Remote Control.
The Newer Bosch models, 2700ES and Bosch 2400ES tankless water heaters have been redesigned to make the installation of the wireless receiver circuit board much easier. The circuit board is basically a plug and play unit.
The TSTAT2 controls the temperature of your water heater and does not have a reset button. If the heater has an error then a code will be on the display of the heater and the user has to go to the heater to reset it from there and should document the error and then see if it returns after resetting.
The TSTAT2 Wireless Remote Control for Bosch 2700ES / 2400ES /2400E / 2400EO / 250SX / 250SXO features the following:
The TSTAT2 remote is particularly useful if you own a jacuzzi or hot tub that requires a hotter water temperature than you normally desire for regular shower use.
The Newer Bosch models, 2700ES and Bosch 2400ES tankless water heaters have been redesigned to make the installation of the wireless receiver circuit board much easier. The circuit board is basically a plug and play unit.
The TSTAT2 controls the temperature of your water heater and does not have a reset button. If the heater has an error then a code will be on the display of the heater and the user has to go to the heater to reset it from there and should document the error and then see if it returns after resetting.
The TSTAT2 Wireless Remote Control for Bosch 2700ES / 2400ES /2400E / 2400EO / 250SX / 250SXO features the following:
- LCD displays temperature, error codes and functions
- Temperature measured in °C or °F
- Low battery level indicator
- 98 feet user range
- Alkaline AA LR6 2x1.5V battery power 915 MHz
- Security lock function
- IP X6 Protection
- Priority function - temperature cannot be modified by other user interface when water is running
Don't forget to periodically change the two AA batteries in your Bosch wireless TSTAT2 thermostat as they will certainly corrode over time. The batteries in TSTAT2 thermostats that are kept in bathrooms will corrode faster than in other less humid environments, such as kitchens. Your batteries should be checked yearly for any signs of corrosion and replaced every five years in any case.
Monday, July 16, 2012
Freeze Protection for Bosch Gas Tankless Water Heaters
Most all of the Bosch gas tankless water heaters come with built in freeze protection. The heaters listed below have built in freeze protection and are approved to be installed in some outside installations.
Our Bosch Outdoor Tankless Water Heaters (Bosch 2700ES with AQOK Outdoor Cap / Bosch 2400ES with AQOK Outdoor Cap/ 125BO / 425HNO / 2400EO / 250SXO) have built in freeze protection and are designed to handle an occasional overnight freeze. They plug directly into the wall and provide freeze protection down to 5 deg F above zero. In order for the freeze prevention kit to provide adequate protection,120V AC must always be supplied to the water heater.They are approved for use in the following areas:
Florida, Georgia, North Carolina, South Carolina, Alabama, Mississippi, Arkansas, Texas, Virginia (only in zip codes beginning with the first three digits 233-237), Arizona (in zip codes beginning with the first three digits 850-857 and 864), Oregon (in zip codes beginning with the first three digits 970-975), Washington (in zip codes beginning with the first three digits 980-986), California (except in zip codes beginning with the first three digits 935 or 961).
Installation instructions state that the water heaters must not be installed in a location where it may be exposed to prolonged freezing temperatures. If the heater must be left in a space which is likely to experience prolonged freezing temperatures, all water must be drained from the heater. If precautions are not taken, resulting damage will not be covered under the warranty. NOTE: Use of agents such as anti-freeze is not permitted as they may cause damage to the water heater's internal components. The freeze prevention will not protect plumbing outside the appliance from freezing. Precautions should be taken.
The Bosch 250SX/2400E/2400ES and 2700ES come with built in freeze protection and these units are for inside installation only. The freeze protection helps the unit if it is installed on the inside of an outside wall where it may be cooler than normal.
Our Bosch Outdoor Tankless Water Heaters (Bosch 2700ES with AQOK Outdoor Cap / Bosch 2400ES with AQOK Outdoor Cap/ 125BO / 425HNO / 2400EO / 250SXO) have built in freeze protection and are designed to handle an occasional overnight freeze. They plug directly into the wall and provide freeze protection down to 5 deg F above zero. In order for the freeze prevention kit to provide adequate protection,120V AC must always be supplied to the water heater.They are approved for use in the following areas:
Florida, Georgia, North Carolina, South Carolina, Alabama, Mississippi, Arkansas, Texas, Virginia (only in zip codes beginning with the first three digits 233-237), Arizona (in zip codes beginning with the first three digits 850-857 and 864), Oregon (in zip codes beginning with the first three digits 970-975), Washington (in zip codes beginning with the first three digits 980-986), California (except in zip codes beginning with the first three digits 935 or 961).
Installation instructions state that the water heaters must not be installed in a location where it may be exposed to prolonged freezing temperatures. If the heater must be left in a space which is likely to experience prolonged freezing temperatures, all water must be drained from the heater. If precautions are not taken, resulting damage will not be covered under the warranty. NOTE: Use of agents such as anti-freeze is not permitted as they may cause damage to the water heater's internal components. The freeze prevention will not protect plumbing outside the appliance from freezing. Precautions should be taken.
The Bosch 250SX/2400E/2400ES and 2700ES come with built in freeze protection and these units are for inside installation only. The freeze protection helps the unit if it is installed on the inside of an outside wall where it may be cooler than normal.
Tuesday, July 3, 2012
Bosch AquaStar 2700ES vs. Bosch Evolution 500 Tankless Water Heaters
The Bosch AquaStar 2700ES is Bosch's top-of-the-line 199,000 BTU retail tankless water heater. As a retail tankless water heater the Bosch 2700 ES can be sold directly to home owners and is the perfect water heater for Do-it-yourselfers (DIY).
The Bosch 2700ES is available in both natural gas (Bosch 2700ES-NG) and liquid propane (Bosch 2700ES-LP). The 2700 ES direct vent tankless water heater requires special 3" or 4" stainless steel vent pipe and can be vented either through the roof or out the side wall. In approved areas the 2700ES can also be mounted outdoors as it comes with freeze protection that is good down to 5 degrees F above zero and provides protection against occasional overnight freezes.
In addition to coming with built-in freeze protection, the AquaStar 2700ES also comes with a pressure relief valve (PRV) and an external water filter.
The Bosch Evolution 500 is identical to the Bosch AquaStar 2700ES. It also comes in natural gas (Bosch Evolution 500 NG) and liquified petroleum (Bosch Evolution 500 LP) models. As a heater in Bosch's professional line of tankless water heaters, however, the Bosch Evolution 500 can only be sold to licensed installers or builders. As a Bosch Professional heater the Evolution 500 comes with a 15 year warranty on the heat exchanger and 5 years on all other parts.
Like the 2700ES, the Evolution 500 direct vent tankless water heater also comes with built-in freeze protection, a PRV and an external water filter. It requires the same Z-Flex Z-Vent 3" or 4" special stainless steel vent pipe.
So, if you intend to have your tankless water heater installed professionally, have your installer visit www.prowaterheatersupply.com and check out the Evolution 500. These heaters are specially priced while supplies last.
The Bosch 2700ES is available in both natural gas (Bosch 2700ES-NG) and liquid propane (Bosch 2700ES-LP). The 2700 ES direct vent tankless water heater requires special 3" or 4" stainless steel vent pipe and can be vented either through the roof or out the side wall. In approved areas the 2700ES can also be mounted outdoors as it comes with freeze protection that is good down to 5 degrees F above zero and provides protection against occasional overnight freezes.
In addition to coming with built-in freeze protection, the AquaStar 2700ES also comes with a pressure relief valve (PRV) and an external water filter.
Like the 2700ES, the Evolution 500 direct vent tankless water heater also comes with built-in freeze protection, a PRV and an external water filter. It requires the same Z-Flex Z-Vent 3" or 4" special stainless steel vent pipe.
So, if you intend to have your tankless water heater installed professionally, have your installer visit www.prowaterheatersupply.com and check out the Evolution 500. These heaters are specially priced while supplies last.
Thursday, May 31, 2012
Gas Conversion for Bosch Retail Gas Tankless Water Heaters
Some of the Bosch Retail gas tankless water heaters can be converted from one gas type to the next, i.e. from Natural Gas (NG) - Liquid Propane (LPG) and also from LPG - NG. The Gas Conversion Kit, part #8719002176 includes a jumper for placement on the control board, a set of instructions for calibrating the gas and air mix and also some stickers to be placed on the heater stating it has been converted.
The tools required for the gas conversion are:
- Flat and Phillips Screwdrivers
- #40 torx driver
- Digital CO2 Gas Combustion Analyzer
- This procedure must be performed by a licensed gas technician
The Bosch Retail Gas tankless water heaters that CAN be converted using the gas conversion kit are the 2700ES/2400ES/2400E/2400EO/250SX/250SXO.
The Bosch Retail Gas tankless water heaters that CANNOT be converted are the 1600H/1600P/1000P and all of the 125 series heaters as they are not designed or approved at all for gas conversion.
Wednesday, May 30, 2012
NEW Ariston GL2.5S & GL4S Mini Tank Heaters
Designed by the world's leading point-of-use water heater manufacturer, the New Ariston GLS series combines Italian design and state of the art features including glass-lined tanks, a 6-year warranty and highest recovery time.
Installing an Ariston electric mini-tank water heater under the sink puts hot water right where you need it - at the point of use. Lightweight and compact and also the Ariston mini tank heaters are great for those long hot water runs from your tank heater or tankless heater and will shorten the wait time for hot water.
The New Ariston GL2.5S mini-tank electric water heater stores 2.5 gallons of hot water.
The New Ariston GL4S mini-tank electric water heater stores 4 gallons of hot water.
Please note: The New Ariston GL2.5S is not the direct replacement for the Ariston GL2.5 as the Ariston Gl2.5S is 10 3/4" in depth and the older Ariston GL2.5 was 10 1/4" deep. The new Ariston GL4S is not the direct replacement for the Ariston GL4 as the GL4S is 13 1/2" in depth and the older Gl4 was 12 1/4" deep. The replacement parts for the new Ariston GL2.5S and the GL4S will not work for the older GL2.5 and GL4 mini tank heaters.
- 6-year warranty on tank
- Glass-lined tank for longer life
- Mounts on wall or floor
- Temperature/pressure relief valve included
- Plugs into standard 120 volt outlet
- Dimensions: GL2.5S-13 3/4" x 13 3/4" x 10 3/4", GL4S-13 3/4" x 13 3/4" x 13 1/2"
- Recovery at 90 Deg F Rise: 7 GPH
- 12.5 AMPS and 1500W Heating Capacity
- Temperature Range: 65 Deg F to 145 Deg F
- Meets ASHRAE 90.1 Standard
- Relief Valve = Installed
The Ariston GL2.5S & GL4S models have a new improved thermostat that features a new sensing probe that is attached to the thermostat and inserts into the cavity of the new element so the heater can adjust temperatures quicker and maintain a more consistent heat.
The new Ariston GL6+S can either be hard wired to an independent breaker or wired to a power cord with 3 pronged plug. Globaltowne has a 6' power cord in stock for the GL6+S.
Saturday, May 26, 2012
Memorial Day Tankless Water Heater Sale!
GlobalTowne is having a Memorial Day Sale on Bosch tankless water heaters this weekend through midnight ET Monday, May 28, 2012. Save up to 10% off!
Just use Promotional Code MEMORIAL at checkout to get up to 10% savings off of our everyday low pricing! Use Promotional Code GIVEME5 for a 5% savings on all of the other products that we sell.
We are also offering Free Ground Shipping on orders over $99.94 through midnight ET Monday, May 28, 2012. Free Ground Shipping is only offered to the lower 48 US States.
You can use the MEMORIAL coupon over the phone -- just remember to mention the coupon code!
Just use Promotional Code MEMORIAL at checkout to get up to 10% savings off of our everyday low pricing! Use Promotional Code GIVEME5 for a 5% savings on all of the other products that we sell.
We are also offering Free Ground Shipping on orders over $99.94 through midnight ET Monday, May 28, 2012. Free Ground Shipping is only offered to the lower 48 US States.
You can use the MEMORIAL coupon over the phone -- just remember to mention the coupon code!
Sunday, February 19, 2012
Bosch Retail Water Heater Program Changes
Bosch Thermotechnology has stopped manufacturing and distributing its retail line of Gas and Propane Bosch tankless water heaters. It appears that Bosch has decided to step back from the do-it-yourself (DIY) model of selling this wonderful brand of gas and liquid propane tankless water heaters directly to homeowners.

As a Bosch Authorized Distributor, GlobalTowne still has a supply of these heaters. So, if you are a homeowner looking for a gas or propane Bosch Tankless Water Heater that you can purchase and install on your own, act quickly as these retail tankless water heaters are going fast!
Just to be clear, the Bosch retail line of PowerStar electric whole-house and point-of-use tankless water heaters and Ariston mini-tank electric water heaters are still being manufactured and distributed. In fact, Bosch is in the process of rolling out newly-improved electric water heaters!
Now for the really good news: Bosch's commitment to their wholesale line of Gas and Propane Bosch Therm tankless water heaters has never been stronger!
The entire retail lineup of Gas and Propane Bosch tankless water heaters are available on the wholesale side of the business. But, even more importantly, the Bosch Pro gas and propane wholesale lineup includes super high efficiency Condensing Tankless Water Heaters that were never available through the retail channel.

Global ProTankless Supply sells the entire wholesale lineup of gas and propane tankless water heaters from prowaterheatersupply.com. The products listed on this web site are available only to licensed installers, contractors, builders and other professionals.
As a part of these program changes, Bosch has retired its retail tankless water heater web site at boschhotwater.com. This retired web site now points to their wholesale web site at bosch-climate.us.
For more information on the Bosch wholesale lineup of gas and propane tankless water heaters for professionals, please call 866.289.4652. If you are a homeowner looking for one of these high-end professional hot water heaters, please have your contractor call.
NyOil II Synthetic Thin-film Lubricant
Globaltowne announces the availability of NyOil II Synthetic Thin-film Lubricant.
If the heat, the humidity, the cold, and the rain don't slow you down, then NyOil II is definitely your lubricant. All new, all synthetic, NyOil II delivers the best lubricating, cleaning, and polishing qualities of a highly refined mineral oil - but it doesn't stop there. Synthesized under laboratory conditions, NyOil II offers the following superior qualities:
- Odorless - no toxic fumes are present when applying.
- Colorless - non-staining and no unsightly messes.
- Tougher film strength - Creates better wear prevention.
- Less volatile - Will last longer than mineral oils.
- Highly stable - Offers superior rust protection. In fact, in the grueling Humidity Cabinet Test, after 100 hours, polished and sandblasted metal panels lubricated with NyOil II showed absolutely no signs of rust.
Whether you work or play in extreme environments, pack a bottle of NyOil II with your gear. It's the superior synthetic lubricant that keeps your tools and equipment working and playing as hard as you.
NyOil II for Pinewood Derby
If your race allows liquid lubricants then NyOil II is the ultimate lubricant!NyOil II is a highly-refined synthetic thin-film lubricant with an ultra-low viscosity. It has a tough film strength for long lasting lubrication. When properly applied, it outperforms dry lubricants including graphite.
NyOil II can be safely used with any brand of pinewood derby wheels. It is colorless, odorless, non-hazardous, and plastic-safe. The key to using a thin-film lubricant is that "less is best". Applying too much lubricant will slow your car down. See our web site for tips on how to make your pinewood derby car the winner!
Call us at 888.726.9752 for details.
Monday, December 12, 2011
Bosch Compress ~ Hybrid Water Heater
Globaltowne Announces the Arrival of the Bosch Compress Hybrid Water Heater
Bosch Compress Heat Pump ~ HP-200-1
ZERO Emissions – Clean electric operation and no venting requirements
SIMPLE installation
10-Year limited warranty
The 50 gallon capacity Bosch Compress Hybrid
Electric Water Heater is ultra efficient and shares
technology similar to an Energy Star® qualified
Refrigerator. Rather than taking heat from inside the
appliance and moving it outside as a refrigerator
does; Bosch hybrid technology takes heat from
outside the appliance and uses it to heat the water!
Using a specially designed heat pump system, the
heat is transferred from the surrounding air to the
water stored in a well insulated storage tank,
resulting in efficient hot water and zero direct
greenhouse gas emissions!
Why Bosch?
For 125 years, Bosch has remained committed to quality, innovation and value within a broad range of products including automotive parts, power tools, home appliances and water heaters. Bosch is highly recommended by professional contractors and is a brand that loyal customers refer to their friends and family.
Heating domestic hot water is a home’s third largest use of
energy. With the technology used in a Bosch Hybrid Water
Heater, this can be reduced significantly, saving valuable
resources and money.
Compared to a traditional tank water heater, the Bosch Hybrid
Water Heater is twice as effective with savings of $307 (59%
reduction on your water heating costs), making it the smart
choice for your water heating needs with an estimated payback
of just 3 years!
Installation
The ideal installation for a Bosch Hybrid Water Heater is in a warm
unconditioned climate such as an attic, basement or garage with at
least 7' x 10' x 10' cubic feet of air space. The efficiency of the Heat
Pump is higher in warmer climates, however you can experience
savings in all climates. This unit directly replaces a 50 gallon water
heater and the energy factor of 2.2 ensures savings.
The Bosch Hybrid Water Heater also cools and dehumidifies
unconditioned air as an extra benefit, saving money and energy on
air conditioning. Installing in unconditioned spaces with air
temperatures between 45°F - 115°F will yield the highest
efficiencies for the Bosch Hybrid Water Heater. With use of the
ducted air option, the Bosch Compress uses the energy of the
unconditioned air to supply cooler, dehumidified air into the air
duct, reducing the overall energy load of your home.
Storage Tank Capacity - 50 Gal.
First Hour Delivery - 58 Gal.
Height - 64.5"
Diameter - 22.4"
Net Weight - 209.4 lbs.
Anode Rod - Magnesium
Air Temperature Range - 45°F to 115°F
Storage Tank Material - Enameled Steel
Air Duct Connections - Exhaust Only
Heating Power - 1.8 kW
Electric Consumption - 0.7 kW
Electric Backup Heating Element - 2 x 4 kW
Voltage (Phase / V / Hz) - 1 / 240 / 60
Electric Connections - Fixed Wire
Built-In Interface - LCD
Operation Modes - Economic Mode - Electric Mode - Auto Mode - Vacation Mode
Hot Water Temp. Range - 100°F to 140°F
Max. Water Presssure - 150 PSI
Water Connections - ¾"
Energy Factor - 2.2
Certification - UL1995
Condensate Drain - ¼"
Temp. & Pressure - Valve Included
Warranty 10-Year Limited Tank & Parts
Bosch Compress Heat Pump ~ HP-200-1
ZERO Emissions – Clean electric operation and no venting requirements
SIMPLE installation
10-Year limited warranty
The 50 gallon capacity Bosch Compress Hybrid
Electric Water Heater is ultra efficient and shares
technology similar to an Energy Star® qualified
Refrigerator. Rather than taking heat from inside the
appliance and moving it outside as a refrigerator
does; Bosch hybrid technology takes heat from
outside the appliance and uses it to heat the water!
Using a specially designed heat pump system, the
heat is transferred from the surrounding air to the
water stored in a well insulated storage tank,
resulting in efficient hot water and zero direct
greenhouse gas emissions!
Why Bosch?
For 125 years, Bosch has remained committed to quality, innovation and value within a broad range of products including automotive parts, power tools, home appliances and water heaters. Bosch is highly recommended by professional contractors and is a brand that loyal customers refer to their friends and family.
Heating domestic hot water is a home’s third largest use of
energy. With the technology used in a Bosch Hybrid Water
Heater, this can be reduced significantly, saving valuable
resources and money.
Compared to a traditional tank water heater, the Bosch Hybrid
Water Heater is twice as effective with savings of $307 (59%
reduction on your water heating costs), making it the smart
choice for your water heating needs with an estimated payback
of just 3 years!
Installation
The ideal installation for a Bosch Hybrid Water Heater is in a warm
unconditioned climate such as an attic, basement or garage with at
least 7' x 10' x 10' cubic feet of air space. The efficiency of the Heat
Pump is higher in warmer climates, however you can experience
savings in all climates. This unit directly replaces a 50 gallon water
heater and the energy factor of 2.2 ensures savings.
The Bosch Hybrid Water Heater also cools and dehumidifies
unconditioned air as an extra benefit, saving money and energy on
air conditioning. Installing in unconditioned spaces with air
temperatures between 45°F - 115°F will yield the highest
efficiencies for the Bosch Hybrid Water Heater. With use of the
ducted air option, the Bosch Compress uses the energy of the
unconditioned air to supply cooler, dehumidified air into the air
duct, reducing the overall energy load of your home.
Storage Tank Capacity - 50 Gal.
First Hour Delivery - 58 Gal.
Height - 64.5"
Diameter - 22.4"
Net Weight - 209.4 lbs.
Anode Rod - Magnesium
Air Temperature Range - 45°F to 115°F
Storage Tank Material - Enameled Steel
Air Duct Connections - Exhaust Only
Heating Power - 1.8 kW
Electric Consumption - 0.7 kW
Electric Backup Heating Element - 2 x 4 kW
Voltage (Phase / V / Hz) - 1 / 240 / 60
Electric Connections - Fixed Wire
Built-In Interface - LCD
Operation Modes - Economic Mode - Electric Mode - Auto Mode - Vacation Mode
Hot Water Temp. Range - 100°F to 140°F
Max. Water Presssure - 150 PSI
Water Connections - ¾"
Energy Factor - 2.2
Certification - UL1995
Condensate Drain - ¼"
Temp. & Pressure - Valve Included
Warranty 10-Year Limited Tank & Parts
Danfoss Snow Melting Systems
Globaltowne and Danfoss ~ Electric heating mats and cables
Electric Snow Melting Systems
Deep-frozen gutters and drain pipes. Rows of sharply pointed icicles. Breakneck icy stairs, pavements, roads and expensive frost bursting of tiles and brickwork. The winter can be a dangerous, troublesome and expensive acquaintance for a homeowner. You do not have to put up with winter troubles. Simple and effective Danfoss heating systems can keep the roof, the drain system and the traffic areas free of ice and snow, and they all work fully automatically.
Ice and Snow Melting on Traffic Areas
Safe walking and driving during winter times! Danfoss GX Snow Melting system operates fully automatic. It automatically registers the need for melting areas and then automatically switches the heat on and off when required. The area is kept free from ice and snow at any time avoiding heavy salt sprinkling, snow shovelling or damage caused by frost. Efficient heat control ensures a good overall economy Danfoss DS-2B and GX850 thermostats and ground sensors ensure that the absolute minimum amount of energy is used to achieve the optimal result.Installation and running costs of Danfoss ice and snow melting system are low when considering the advantages of the system as for instance preventing the efforts of snow shovelling and salting. Furthermore the repairing costs caused by ice, snow and salt are saved.
Applicable for most surfaces
The Danfoss GX snow melting system is applicable for the most typical surfaces such as asphalt, concrete and interlocking stones. The most typical Danfoss GX ice and snow melting applications on ground are parking lots, driveways, pavement, outdoor steps, etc.
Electric Snow Melting Mats and Cables
Improve safety by providing instantaneous relief from snow and ice and increase your bottom and by reducing the costs associated with applying chemicals, owning snow clearing machinery or hiring outside services.
Twin conductor cable
Single point connection
Easy and flexible installation
Durable construction
Silent, efficient and safe
Ideal for driveways, parking lots, sidewalks, stairs, ramps, bridges and many other applications
For use in concrete, asphalt, and under pavers
Zero EMF's (Electromagnetic fields)
Heating mats significantly reduce installation time
Genuine ten year non-prorated warranty
DS-2B Snow Melt Controller
The DS-2B snow melt controller is primarily designed for pavement snow melting applications. It can be used as stand-alone or as a sensor for larger control systems.
Housed in a weatherproof enclosure
Adjustable temperature trigger point
Adjustable delay off drying time
Selectable low temperature cutoff
Manual override
Remote control and monitor capabilities
Two year warranty
DS-5 Snow and Ice Melting Control
The DS-5 Control is designed primarily for pavement snow and ice melting applications. It can be used as a stand-alone controller or as a sensor for larger control systems.
Housed in a weatherproof enclosure
Adjustable temperature trigger point
Adjustable delay off drying time
Selectable low temperature cut-off
Manual override
Remote control and monitor capabilities
Two year warrantyThe DS-5 differs from the DS-2B as the DS-5 can handle a maximum heating load of 60A.
GX 850 Dual Zone Automatic Control Panel
The award winning GX 850 ACP is the most optimal solution for keeping any area free of ice and snow. The GX 850 acts on information received from sensor(s) which register temperature and moisture, then calculate the information, ensuring that the heat will only be turned on when snow and/or ice is present. The result is optimal performance with maximum energy savings and minimum operating costs.
User interface allows total control of snow melting system set points
Set to maximum melting or maximum energy savings or anywhere in between
Dual zone feature allows for energy savings and lower impact draw
Digital sensors provide precise feedback on snow and ice conditions
Fault finding program detects and alarms on faults
Can be field upgraded to take advantage of new features Two year warranty
Please visit www.globaltowne.com or call 888-726-9752
Electric Snow Melting Systems
Deep-frozen gutters and drain pipes. Rows of sharply pointed icicles. Breakneck icy stairs, pavements, roads and expensive frost bursting of tiles and brickwork. The winter can be a dangerous, troublesome and expensive acquaintance for a homeowner. You do not have to put up with winter troubles. Simple and effective Danfoss heating systems can keep the roof, the drain system and the traffic areas free of ice and snow, and they all work fully automatically.
Ice and Snow Melting on Traffic Areas
Safe walking and driving during winter times! Danfoss GX Snow Melting system operates fully automatic. It automatically registers the need for melting areas and then automatically switches the heat on and off when required. The area is kept free from ice and snow at any time avoiding heavy salt sprinkling, snow shovelling or damage caused by frost. Efficient heat control ensures a good overall economy Danfoss DS-2B and GX850 thermostats and ground sensors ensure that the absolute minimum amount of energy is used to achieve the optimal result.Installation and running costs of Danfoss ice and snow melting system are low when considering the advantages of the system as for instance preventing the efforts of snow shovelling and salting. Furthermore the repairing costs caused by ice, snow and salt are saved.
Applicable for most surfaces
The Danfoss GX snow melting system is applicable for the most typical surfaces such as asphalt, concrete and interlocking stones. The most typical Danfoss GX ice and snow melting applications on ground are parking lots, driveways, pavement, outdoor steps, etc.
Electric Snow Melting Mats and Cables
Improve safety by providing instantaneous relief from snow and ice and increase your bottom and by reducing the costs associated with applying chemicals, owning snow clearing machinery or hiring outside services.
Twin conductor cable
Single point connection
Easy and flexible installation
Durable construction
Silent, efficient and safe
Ideal for driveways, parking lots, sidewalks, stairs, ramps, bridges and many other applications
For use in concrete, asphalt, and under pavers
Zero EMF's (Electromagnetic fields)
Heating mats significantly reduce installation time
Genuine ten year non-prorated warranty
DS-2B Snow Melt Controller
The DS-2B snow melt controller is primarily designed for pavement snow melting applications. It can be used as stand-alone or as a sensor for larger control systems.
Housed in a weatherproof enclosure
Adjustable temperature trigger point
Adjustable delay off drying time
Selectable low temperature cutoff
Manual override
Remote control and monitor capabilities
Two year warranty
DS-5 Snow and Ice Melting Control
The DS-5 Control is designed primarily for pavement snow and ice melting applications. It can be used as a stand-alone controller or as a sensor for larger control systems.
Housed in a weatherproof enclosure
Adjustable temperature trigger point
Adjustable delay off drying time
Selectable low temperature cut-off
Manual override
Remote control and monitor capabilities
Two year warrantyThe DS-5 differs from the DS-2B as the DS-5 can handle a maximum heating load of 60A.
GX 850 Dual Zone Automatic Control Panel
The award winning GX 850 ACP is the most optimal solution for keeping any area free of ice and snow. The GX 850 acts on information received from sensor(s) which register temperature and moisture, then calculate the information, ensuring that the heat will only be turned on when snow and/or ice is present. The result is optimal performance with maximum energy savings and minimum operating costs.
User interface allows total control of snow melting system set points
Set to maximum melting or maximum energy savings or anywhere in between
Dual zone feature allows for energy savings and lower impact draw
Digital sensors provide precise feedback on snow and ice conditions
Fault finding program detects and alarms on faults
Can be field upgraded to take advantage of new features Two year warranty
Please visit www.globaltowne.com or call 888-726-9752
Sunday, December 11, 2011
Recirculation Pumps~ Armstrong

Recirculation Pumps can be used to provide instant hot water at a faucet or from radiant floors using water or a glycol type liquid for floor warming.
Armstrong is a leader in pump technology and these pumps are made in New York and Canada in the Buffalo / Niagara area.
Used with a tankless heater, the recirculation pump circulates water from a small tank heater within a loop to each faucet. The pump can have a timer
and a temperature sensor so the loop stays warm but the mini tank water heater is not on all the time. When a faucet is turned on, the tankless heater sees the flow and turns on and the heated water flows through a check valve and to the open faucet.
Armstrong has an all in one system called the ASTRO EXPRESS. The Astro Express System works like a thermostat.The snap-acting valve opens and closes to circulate hot water so it stays at a specific temperature throughout the distribution system. Hot water at each tap stays hot, and cold water stays cold.
A timer automatically ensures that the water is recirculated regularly; and can be set for multiple activation periods per day. It can be set to circulate water only during normal usage hours (i.e. not in the middle of the night when everyone is asleep). The timer includes manual on/off overrides to normal automatic operation.
Each system comes with one valve, which is installed at the faucet furthest away from the water heater. This ensures that hot water is delivered to all the faucets in between. A home that has a distribution line with a number of branches, will need a valve for the faucet at the end of each branch. Additional valves are available separately

The Astro 20 BU-T circulator is a small pump with twice the capacity of other circulators. It can handle more flow to more destinations (up to 5 valves) for the kind of “branch plumbing” that can make hot water distribution in a large or ranch-style home such a challenge.
Most dedicated return systems are oversized and have a short duty cycle when the aquastat is activated. Our injection system uses lower flow to maintain a more stable water temperature at the hot water faucet and prevent noise and erosion. Plus, larger openings ensure easier flow, so several people can turn on taps throughout the house and they will all get hot water instantly.
FEATURES
- 24-hour clock timer
- 15 minute user selectable intervals
- On/Off/Auto switch_ 120Vac, 1/25 HP, .5A
- 5 ft power cord_ Max head: 5.8 ft
- Max flow: 11.5 GPM_ Brass full unions
- EPDM O-rings
- 1 male and 2 female ¾” tailpieces
- Wet rotor design ensures virtually silent operation
- Bronze housing for potable water use
- High starting torque overcomes mineral build-up
- Built for durability with bronze casing, stainless steel shaft and graphite bearings
STRONGER
The Astro Express is a clear winner for quality, durability and strength. With a rugged, forged-brass valve and a powerful circulator with the capacity of anything else on the market.
FASTER
No dedicated lines make for a quick installation, and quality parts and an adjustable flow rate mean zero maintenance.Our one-size-fits-all solution ensures you’ll always have the right model on your truck. Install it in as little as 30 minutes flat.
BETTER
Offer your customers something more than just a standard recirculation system.
Give them something better: the Astro Express System is the highest-quality, most dependable system on the market. The pump can handle the widest range of homes, from a small bungalow to a sprawling ranch-style house. The system is powerful enough to ensure that several faucets can be in use at the same time throughout the house, without any impact on temperature or speed of hot water delivery
Call us at 888-726-9752
Saturday, December 10, 2011
Humphrey Indoor Gas Lights Now in Stock!
We are pleased to report that we now have all of the Humphrey Gas Lights in stock. We have large quantities of these Humphrey Indoor Gas Lights available in a variety of colors, including Rustic Walnut, Hunter Green, Pebble Grey and Natural Almond. We have both preformed mantle lights as well as tie-on mantle gas lights.
We also have a large supply of mantles, including preformed mantles, tie-on mantles and clip-on mantles. We also carry burner noses, seals, spare globes and pendant kits.
Humphrey Gas Lights and Accessories are the perfect Christmas present. There is still time to receive these products before Christmas. Order now while supplies last.
Steve
Subscribe to:
Posts (Atom)











