Bosch Therm 330PN Replacing the Bosch Aquastar 38B

The Bosch Therm 330PN gas tankless water heater is a point-of-use water heater designed to provide instant hot water for two sinks. It can, in some locals be used to provide hot water for a single low flow shower.  

The Bosch 330PN is 75,000 BTU's and can deliver 2.6 GPM of hot water at a 45 degree F temperature rise. A regular shower head delivers about 2.0 - 2.5 GPM, so the Bosch 330PN is right on the edge for delivering water for a hot shower.

However, if you live in a warm climate, such as Texas, Southern California, Florida, Arizona, etc, then you probably do not need to raise the water temperature by 45 degrees, so the 330PN can work for a single shower.

Also, if you use a low-flow shower head that reduces your flow to say 1.5 GMP, then again you can have a hot shower with the Bosch 330PN.

We would not recommend the Bosch Therm 330PN for a regular flow shower head in New York -- it just will not be able to keep up and provide you with a hot shower due to the cold incoming water.  The Bosch Therm 330PN is not designed or approved for preheated inlet water..
The Bosch 330PN is a good replacement for the older Bosch Aquastar 38B. The 38B was 40,000 BTU's and only delivered about 1.3 GPM at the same 45 degree F temperature rise. So, the 330PN really is a much stronger water heater than the 38B ever was!

The Bosch Therm 330PN takes the same 4" venting as the 38B did and must be vented vertical up through the roof.  The 330PN CANNOT be powervented out the sidewall of the building.

The Bosch 330PN comes in both Natural Gas (NG) and Liquid Propane (LPG) models.

The Bosch 330PN is designed for heating potable water only and is not approved for space heating applications.

Humphrey Tie-On Burner Nose L12-11A Back in Stock!

For over a year the manufacturer has had the Humphrey Tie-On Burner Nose (L12-11A) on backorder.

As of today we again have this Humphrey / Paulin replacement part in stock!

Order online at www.globaltowne.com.

Procedure for Programming The Wireless Remote TSTAT2

The Bosch Wireless Remote Control (TSTAT2) is used to remotely control the temperature of the Bosch Therm tankless water heater. The TSTAT2 does NOT have the ability to remotely reset the Bosch Therm hot water heater. Below is a more in depth procedure for installing the remote control.

The Bosch Wireless Remote Control (TSTAT2) is designed to work with the following Bosch Therm Tankless Water Heaters: C 1210 ESC, C 1210 ES, C 920 ESC, C 920 ES, C 1050 ES, C 800 ES, Integra 500, C 950 ES, 940ES, 940ESO, 715 ES, Evolution 500 and 830ES as well as the Bosch AquaStar 2700ES and 2400ES heaters.

TSTAT2 Remote Control Installation:

On the "heater" control panel, press and hold Program key while
pressing the ON/OFF button to ON.  Release program key when LCD
displays “188”.  LCD shows “P2”. If not, repeat previous step.

1. Press the + button on the heater to select "P3".  Press and hold Program 
key again for 1 sec.  LCD shows one number and one rotating digit. If not, 
repeat previous step.

The number represents the remote control which is to be registered, the
first remote control will be registered with number “0”, the second with
number “1” and so on.  The rotating digit shows that the electronics is 
expecting a registration and waiting for response from wireless remote.  
If the LCD fails to show a number and rotating digit after repeated attempts, 
double check the wire connections made in section 5.1.

2.  Hold wireless remote control in front of the control panel on the heater and
simultaneously press remote control buttons until the temperature indication 
is shown on the remote control LCD.

3.   Press ON / OFF button on the front of the heater to OFF position and then
back ON.

4.  Press buttons + or - on the remote to reach desired temperature.

New remote control is programmed.

To program a 2nd or 3rd remote to the same heater, follow the steps above and 
then after the remote is programmed you will be able to use the first or 2nd or 
3rd remote to raise or lower the temperature on the heater.  Please remember
the remotes cannot be used to reset the heater if an error code should appear.